Products
0102030405
WENK Pneumatic DSNU Stainless Steel Mini Cylinder
Product Detail
Acting Mode |
Double Acting |
Working Media |
Cleaned Air |
Working Pressure |
0.1~1.0Mpa |
Working Temperature Range |
-10℃~60℃ |
Piston Speed |
50~750mm/s |
Body Material |
Stainless Steel |
DSNU Stainless Steel Mini Cylinder User Manual
Technical Specifications
- Bore range: 8-63 mm
- Stroke range: 5-500 mm
- Operating pressure: 0.1-1.0 MPa
- Operating temperature: -20~80°C
- Operating medium: Clean air (filtered through 40μm filter)
- Cushioning type:
- Type P: Elastic cushion rings at both ends
- Type PPV: Adjustable pneumatic cushioning at both ends
- Type PPS: Self-adjusting pneumatic cushioning at both ends
- Mounting options: Multiple mounting options including direct mounting, flange mounting, foot mounting, etc.
- Piston rod thread: Internal or external thread optional
- Pneumatic connection: M5 or G1/8, G1/4, G3/8 (depending on bore size)
Installation Steps
-
Pre-installation Preparation
- Check if the cylinder model matches the requirements
- Ensure the working environment meets the cylinder's operating temperature and pressure range
- Prepare necessary installation tools and accessories
-
Mounting Position Selection
- Vertical installation is recommended with the drain port facing downward
- Ensure sufficient space at the installation location to avoid interference with other components during cylinder movement
- Ensure the mounting surface is flat and clean
-
Piping Connection
- Connect the pneumatic system in the order of air inlet → filter → pressure regulator → air outlet
- Use appropriate sealing materials to ensure good sealing at connections
- Avoid excessive bending of pipes, which may affect air flow
-
Securing the Cylinder
- Use appropriate mounting accessories to fix the cylinder in position
- Ensure secure fixation to avoid vibration affecting cylinder performance
-
Connecting Electrical Components (if required)
- If using magnetic switches for position detection, install and connect according to the instructions
Operation Guide
-
Initial Start-up
- Gradually increase air pressure and observe cylinder operation
- Check if the cylinder runs smoothly without abnormal noise
- Confirm if the cushioning effect is appropriate
-
Normal Operation
- Ensure working pressure is within the specified range
- Regularly check cylinder operating status
- Record cylinder operating time and maintenance conditions
-
Speed Control
- Control the cylinder's operating speed by adjusting the flow control valve
- Exhaust throttling is recommended for horizontally mounted cylinders
- Intake throttling is recommended for vertically mounted cylinders
Maintenance
-
Daily Inspection
- Check for air leakage
- Inspect piston rod surface for damage or corrosion
- Check if mounting accessories are loose
-
Regular Maintenance
- Every 3 months: Clean the cylinder exterior and check connections
- Every 6 months: Inspect seal condition and replace if necessary
- Annually: Perform a comprehensive inspection including internal components
-
Lubrication
- Generally, no additional lubrication is required
- If the pneumatic system uses lubricating oil, ensure compatibility with seals
Precautions
-
Safety Precautions
- Ensure air supply is cut off before installation and maintenance
- Avoid use exceeding the rated pressure
- Prevent the cylinder from severe impact or vibration
-
Usage Limitations
- Do not use beyond the specified temperature range
- Do not use in environments with corrosive gases or liquids unless specially designed anti-corrosion models are selected
- Do not use in dusty or particle-contaminated environments unless dust-proof devices are installed
-
Troubleshooting
- If abnormal cylinder operation is found, stop use immediately and inspect
- Common faults and solutions:
- Air leakage: Check seals and replace if necessary
- Unstable operation: Check cushion adjustment and adjust speed control
- Piston rod bending: Check if load is excessive and installation is correct
Our Commitments & Core Advantages
1. We are a factory specializing in the production of pneumatic components, with mature manufacturing experience and technology.
2. We manufacture and supply a wide range of series and specifications of air cylinders and pneumatic components, providing you with flexible options.
3. We can undertake the customization business of various pneumatic components according to the specific needs of customers.
We adhere to the service concept of efficiency and thoughtfulness, making you feel comfortable throughout the cooperation process, just as smooth as cooperating with a close friend.