Products
0102030405
WENK Pneumatic F-SC Magnetic Switch Bracket
Product Detail
Working Media |
Cleaned Air |
Body Material |
Plastic |
F-SC Magnetic Switch Bracket User Guide
Product Introduction
The F-SC Magnetic Switch Bracket is a high-quality aluminum alloy mounting bracket manufactured by WENK Pneumatic, specifically designed for fixing magnetic switches on SC series cylinders. This bracket is made of premium aluminum alloy material, featuring light weight, high strength, and corrosion resistance. The bracket has a high fit with the cylinder, no gaps, ensuring the optimal sensing distance between the magnetic switch and the cylinder, improving the accuracy and stability of position detection. The product is available in various specifications (F-SC32, F-SC63, F-SC80, F-SC125, F-SC160, F-SC250), each suitable for different bore sizes of SC series cylinders.
Installation Instructions
-
Preparation:
- Confirm that the bracket specification matches the cylinder model (e.g., F-SC32 is suitable for SC32-SC50 cylinders)
- Prepare necessary tools: hex wrench or Phillips screwdriver
- Check if the bracket is intact, no deformation or damage
-
Installation Steps:
- Insert the magnetic switch into the bracket's slot, ensuring the switch is fully seated
- Align the bracket's rod part with the cylinder's rod slot, gently push in
- Adjust the bracket's position on the cylinder according to the required detection position
- Fix the bracket with screws or clips, ensuring the bracket is stable and does not loosen
- Connect the magnetic switch wires, ensuring correct wiring
-
Installation Notes:
- Ensure the cylinder surface is clean, free of oil or impurities before installation
- The bracket must completely fit the cylinder surface, avoiding gaps
- The sensing surface of the magnetic switch should face the magnetic ring inside the cylinder
- Avoid installation and use in high temperature, strong magnetic field, or corrosive environments
Preparation:
- Confirm that the bracket specification matches the cylinder model (e.g., F-SC32 is suitable for SC32-SC50 cylinders)
- Prepare necessary tools: hex wrench or Phillips screwdriver
- Check if the bracket is intact, no deformation or damage
Installation Steps:
- Insert the magnetic switch into the bracket's slot, ensuring the switch is fully seated
- Align the bracket's rod part with the cylinder's rod slot, gently push in
- Adjust the bracket's position on the cylinder according to the required detection position
- Fix the bracket with screws or clips, ensuring the bracket is stable and does not loosen
- Connect the magnetic switch wires, ensuring correct wiring
Installation Notes:
- Ensure the cylinder surface is clean, free of oil or impurities before installation
- The bracket must completely fit the cylinder surface, avoiding gaps
- The sensing surface of the magnetic switch should face the magnetic ring inside the cylinder
- Avoid installation and use in high temperature, strong magnetic field, or corrosive environments
Usage Instructions
-
Basic Operation:
- After the bracket is installed, the magnetic switch will automatically sense the position of the cylinder piston
- When the cylinder piston moves to the magnetic switch position, the switch triggers and outputs a signal
- The detection point can be changed by adjusting the bracket's position on the cylinder
-
Position Adjustment:
- Loosen the bracket's fixing screws
- Move the bracket along the cylinder axis to the desired position
- Retighten the fixing screws to ensure the bracket position is fixed
- Test whether the magnetic switch triggers at the correct position
-
Usage Notes:
- Avoid frequent adjustment of the bracket position to prevent affecting the fixing effect
- Regularly check if the bracket is firmly fixed to prevent loosening
- Pay attention to protecting the magnetic switch wires to avoid pulling or damage
- Ensure the magnetic ring on the cylinder piston is intact, otherwise the sensing effect will be affected
Basic Operation:
- After the bracket is installed, the magnetic switch will automatically sense the position of the cylinder piston
- When the cylinder piston moves to the magnetic switch position, the switch triggers and outputs a signal
- The detection point can be changed by adjusting the bracket's position on the cylinder
Position Adjustment:
- Loosen the bracket's fixing screws
- Move the bracket along the cylinder axis to the desired position
- Retighten the fixing screws to ensure the bracket position is fixed
- Test whether the magnetic switch triggers at the correct position
Usage Notes:
- Avoid frequent adjustment of the bracket position to prevent affecting the fixing effect
- Regularly check if the bracket is firmly fixed to prevent loosening
- Pay attention to protecting the magnetic switch wires to avoid pulling or damage
- Ensure the magnetic ring on the cylinder piston is intact, otherwise the sensing effect will be affected
Maintenance
-
Regular Inspection:
- Regularly check if the bracket is loose or displaced
- Check if the bracket surface is corroded or damaged
- Confirm if the connection between the magnetic switch and the bracket is stable
- Test the sensing sensitivity of the magnetic switch
-
Cleaning and Maintenance:
- Use a clean cotton cloth to wipe the bracket surface, keeping it clean
- If there is oil, clean with neutral detergent and then dry
- Avoid using corrosive cleaners or solvents
- Regularly inspect and clean impurities on the contact surface between the bracket and the cylinder
-
Maintenance Cycle:
- Under normal conditions, inspection and maintenance are recommended every 3-6 months
- In harsh environments, the maintenance cycle should be appropriately shortened
- If the bracket is found to be deformed or damaged, it should be replaced in time
Regular Inspection:
- Regularly check if the bracket is loose or displaced
- Check if the bracket surface is corroded or damaged
- Confirm if the connection between the magnetic switch and the bracket is stable
- Test the sensing sensitivity of the magnetic switch
Cleaning and Maintenance:
- Use a clean cotton cloth to wipe the bracket surface, keeping it clean
- If there is oil, clean with neutral detergent and then dry
- Avoid using corrosive cleaners or solvents
- Regularly inspect and clean impurities on the contact surface between the bracket and the cylinder
Maintenance Cycle:
- Under normal conditions, inspection and maintenance are recommended every 3-6 months
- In harsh environments, the maintenance cycle should be appropriately shortened
- If the bracket is found to be deformed or damaged, it should be replaced in time
Troubleshooting
-
Magnetic Switch Does Not Trigger:
- Check if the bracket position is correct, adjust to within the cylinder magnetic ring range
- Confirm if the bracket is completely fitted to the cylinder surface
- Check if the magnetic switch is damaged, try replacing the switch
- Confirm if the magnetic ring on the cylinder piston is intact
-
Bracket Loose or Displaced:
- Retighten the bracket's fixing screws
- Check if the bracket is deformed, replace if deformed
- Ensure the mounting surface is clean, no oil or impurities affecting fixation
-
Unstable Induction Signal:
- Check if the bracket is completely fitted to the cylinder, eliminate gaps
- Adjust the position of the magnetic switch in the bracket to ensure the sensing surface is facing the magnetic ring
- Check if there is external magnetic field interference, keep away from strong magnetic field equipment
- Confirm if the power supply voltage is stable and the fluctuation is within the allowable range
Magnetic Switch Does Not Trigger:
- Check if the bracket position is correct, adjust to within the cylinder magnetic ring range
- Confirm if the bracket is completely fitted to the cylinder surface
- Check if the magnetic switch is damaged, try replacing the switch
- Confirm if the magnetic ring on the cylinder piston is intact
Bracket Loose or Displaced:
- Retighten the bracket's fixing screws
- Check if the bracket is deformed, replace if deformed
- Ensure the mounting surface is clean, no oil or impurities affecting fixation
Unstable Induction Signal:
- Check if the bracket is completely fitted to the cylinder, eliminate gaps
- Adjust the position of the magnetic switch in the bracket to ensure the sensing surface is facing the magnetic ring
- Check if there is external magnetic field interference, keep away from strong magnetic field equipment
- Confirm if the power supply voltage is stable and the fluctuation is within the allowable range
Our Commitments & Core Advantages
1. We are a factory specializing in the production of pneumatic components, with mature manufacturing experience and technology.
2. We manufacture and supply a wide range of series and specifications of air cylinders and pneumatic components, providing you with flexible options.
3. We can undertake the customization business of various pneumatic components according to the specific needs of customers.
We adhere to the service concept of efficiency and thoughtfulness, making you feel comfortable throughout the cooperation process, just as smooth as cooperating with a close friend.
