Products
0102030405
WENK Pneumatic MHF2 Series Slim Pneumatic Gripper
Product Detail
| Bore Size | 8 | 12 | 16 | 20 |
| Effective Clamping Force | 19N | 48N | 90N | 141N |
| Operating Pressure | 0.15~0.7Mpa | 0.1~0.7Mpa | ||
| Actuation Method | Double-Acting | |||
| Media Temperature | -10℃~60℃ | |||
| Repeatability | ±0.05mm | |||
| Material | Aluminum Alloy | |||
MHF2 Thin Pneumatic Finger User Guide
Product Specifications
- Bore sizes: 8mm, 12mm, 16mm, 20mm, 25mm, 32mm
- Action type: Double acting
- Operating fluid: Compressed air
- Operating pressure range: 0.15~0.7MPa (for 8mm bore), 0.1~0.7MPa (for other bores)
- Ambient and fluid temperature: -10~60°C (non-frozen)
- Repeatability: ±0.05mm (for 8mm bore), ±0.04mm (for other bores)
- Maximum operating frequency:
- Short stroke: 120 cycles per minute
- Medium stroke: 60 cycles per minute
- Long stroke: 30 cycles per minute
- Gripping force: Up to 141N (for 20mm bore at 0.5MPa)
Installation Steps
-
Confirm installation location and space requirements
- Ensure mounting surface is flat and sufficiently strong
- Reserve appropriate space for piping and wiring
-
Secure the gripper body
- Use suitable screws to fix the gripper to the mounting surface
- For MHF2-8D model, use 2 M3×0.5 threaded holes (depth 7mm)
- Ensure secure installation to avoid precision issues due to looseness
-
Install fingers and accessories
- Install appropriate fingers or fixtures according to application requirements
- Use accessory mounting threaded holes to fix additional devices
-
Piping connection
- Confirm the opening and closing direction of the gripper
- Connect to air ports using suitable air tubes and fittings
- Ensure piping is properly sealed without leaks
-
Magnetic switch installation (optional)
- Install magnetic switches if position detection is required
- Adjust switch position to accurately detect finger position
Operation Guide
-
Pre-start checks
- Confirm air supply pressure is within specified range
- Check piping connections for correctness
- Ensure operating environment temperature is within allowable range
-
Basic operation
- Control the opening and closing of fingers by controlling the supply and exhaust of compressed air
- Finger opening: Compressed air enters from the "open port"
- Finger closing: Compressed air enters from the "close port"
-
Gripping force adjustment
- Adjust gripping force by regulating working air pressure
- Higher air pressure results in greater gripping force
- Select appropriate gripping force based on workpiece weight and material
-
Stroke adjustment
- Choose appropriate stroke length (short, medium, long) as needed
- Ensure workpiece is stably clamped throughout the entire stroke range
Maintenance
-
Daily inspection
- Check for piping leaks
- Confirm smooth operation of the gripper
- Inspect fingers and fixtures for wear or damage
-
Regular maintenance
- Every 3 months:
- Clean the exterior of the gripper
- Check for loose mounting screws
- Inspect wear on fingers and fixtures
- Every 6 months:
- Replace grease
- Check the working status of magnetic switches
- Perform comprehensive functional testing
- Every 3 months:
-
Lubrication
- Use recommended lubricating oil or grease
- Avoid over-lubrication to prevent workpiece contamination or precision issues
Safety Precautions
- Read this user guide carefully before operation
- Ensure air supply pressure is within specified range to avoid equipment damage or safety accidents due to excessive pressure
- Cut off air supply before installation and maintenance
- Avoid use in environments with corrosive gases, dust, or high temperatures unless the equipment is specially treated
- Do not exceed the rated load and operating frequency of the equipment
- Regularly inspect equipment status to identify and address potential issues promptly
- Immediately stop use and perform inspection if abnormal conditions are found
Our Commitments & Core Advantages
1. We are a factory specializing in the production of pneumatic components, with mature manufacturing experience and technology.
2. We manufacture and supply a wide range of series and specifications of air cylinders and pneumatic components, providing you with flexible options.
3. We can undertake the customization business of various pneumatic components according to the specific needs of customers.
We adhere to the service concept of efficiency and thoughtfulness, making you feel comfortable throughout the cooperation process, just as smooth as cooperating with a close friend.