Products
0102030405
WENK Pneumatic SDA Series Thin Cylinder
Product Detail
Acting Mode |
Double Acting |
Working Media |
Cleaned Air |
Working Pressure |
0.1-0.9Mpa(1-9kgf/cm²） |
Proof Pressure |
1.35Mpa(13.5kgf/cm²） |
Working Temperature Range |
-5-70° |
Buffering Model |
With |
Body Material |
Aluminum Alloy |
SDA Compact Thin Cylinder User Manual
Technical Specifications
- Bore size range: 12mm - 100mm
- Stroke range: 5mm - 100mm+
- Operating pressure: 0.1 - 0.9MPa
- Proof pressure: 1.5MPa
- Operating temperature: -5°C - 70°C
- Operating speed: 30 - 500mm/s (double acting), 100 - 500mm/s (single acting)
- Cushion type: Fixed bumper
- Working medium: Clean air filtered through 40μm filter
- Port size: M5×0.8, G1/8", G1/4", G3/8"
- Mounting options: Multiple mounting options available (basic type, LB, FA, SDB, etc.)
Structural Features
- Cylinder bore treated with rolling followed by hard anodizing, providing excellent wear resistance and durability
- Piston seal adopts heterogeneous two-way seal structure with compact dimensions and oil storage function
- Magnetic switch slots around the cylinder body for easy installation of position sensors
- Multiple mounting accessories available
- Riveted structure connects cylinder body and end covers, piston and piston rod for reliable connection
- Compact design effectively saves installation space
- All cylinders in this series come with built-in magnet for position detection
Installation Steps
-
Pre-installation Preparation
- Verify that the cylinder model and specifications meet requirements
- Ensure the installation environment is clean to prevent dust and debris from entering the cylinder
- Prepare necessary installation tools and accessories
-
Mounting Method
- Select the appropriate mounting method based on application requirements
- Ensure secure installation to avoid vibration during operation
- Pay attention to the cylinder's movement direction, ensuring alignment with the load direction
-
Piping Connection
- Connect the pipeline in the order: air supply → filter → pressure regulator → cylinder
- Use appropriate sealing materials to ensure good sealing of pipe connections
- Clean the pipeline before connection to prevent debris from entering the cylinder
-
Sensor Installation
- Magnetic switches can be installed externally using the cylinder's built-in magnet ring
- Install and adjust the position correctly according to the sensor manual
Operation Guide
-
Pre-start Check
- Confirm that the air supply pressure is within the specified range
- Check that the pipeline connections are correct
- Ensure there are no obstacles in the cylinder's movement range
-
Operation
- Slowly open the air supply valve and gradually increase pressure
- Observe whether the cylinder operates smoothly without abnormal noise
- If abnormalities are found, stop use immediately and check the cause
-
Speed Control
- Control the cylinder speed by adjusting the flow control valve
- Speed adjustment should be done gradually to avoid sudden changes
Maintenance
-
Daily Inspection
- Regularly check the cylinder operation status for abnormal noise or leakage
- Inspect pipe connections for looseness or damage
- Keep the cylinder exterior clean
-
Regular Maintenance
- Check the condition of seals every 3 months
- Perform a comprehensive inspection and maintenance every 6 months
- Replace wearing parts timely based on usage environment and frequency
-
Lubrication
- The cylinder is equipped with self-lubricating bearings and generally does not require additional lubrication
- In harsh environments or with high-frequency use, an appropriate amount of lubricating oil can be added through an oil mist device
Precautions
-
Safety Precautions
- Always cut off the air supply before installation and maintenance
- Avoid using the cylinder beyond the rated pressure
- Never place hands or other body parts within the cylinder's movement range
-
Usage Limitations
- Avoid use in corrosive environments unless special materials are selected
- Do not use beyond the specified temperature range
- Avoid excessive lateral loads to prevent affecting cylinder life
-
Special Environment Handling
- In environments with high humidity, dust, water droplets, oil dust, or welding slag, necessary protective measures should be taken
- In low-temperature environments, anti-freezing measures should be taken to prevent water in the system from freezing
Our Commitments & Core Advantages
1. We are a factory specializing in the production of pneumatic components, with mature manufacturing experience and technology.
2. We manufacture and supply a wide range of series and specifications of air cylinders and pneumatic components, providing you with flexible options.
3. We can undertake the customization business of various pneumatic components according to the specific needs of customers.
We adhere to the service concept of efficiency and thoughtfulness, making you feel comfortable throughout the cooperation process, just as smooth as cooperating with a close friend.